Skip to content
For Media & Publishers

Broadcast the news everywhere it's watched

Newsrooms and publishers reach audiences across every platform at once — with the reliability and quality live news demands.

Live now4 feeds
LIVE
LIVE
LIVE
LIVE
Status
On air
Passthrough
Your encoder quality
SRT
Resilient ingest
Custom
RTMP destinations
Slate
Continuity on drop

A broadcast stack built for newsrooms

Simulcast everywhere

Push one feed to YouTube, Facebook, X, and your own site simultaneously.

No re-encode in the middle

Your feed is forwarded to each destination as it arrives, so adding platforms costs nothing in quality.

Continuity when the feed drops

On the Control plan, if your encoder disconnects, a holding slate keeps the destinations alive until you are back, instead of the broadcast simply ending.

An archive as you broadcast

Switch recording on and the session is captured while it airs, so the archive is a by-product rather than a second job.

Health you can read at a glance

A health score from 0 to 100 and Stream Doctor's plain-language advice show what is wrong with a feed while it is still on air.

Clips for socials

Pick the recording in Clips, mark the segment and export it vertical for Reels, Shorts and TikTok.

Putting a newsroom feed on every platform

For a programme that already exists, coming out of a hardware encoder, vMix or OBS. StreamRove changes where it lands, not how you make it.

  1. Send the programme feed over SRT

    In the stream's connection details, pick the SRT tab and copy the address into your encoder in caller mode, with the latency set to 500 ms. The feed has to be H.264 video with AAC audio. RTMPS works too when the line is clean.

  2. Match the strictest destination

    One feed goes to every platform and has to suit all of them. Stay at 6,000 kbps or less with Twitch on the list, and with Facebook at 30 fps; Facebook at 60 fps takes up to 9,000 and Kick 8,000. StreamRove plans YouTube at up to 12,000. Keyframes every 2 seconds, at a constant bitrate.

  3. Add the destinations

    YouTube, Twitch and Kick connect in one click. For Facebook, X (through Live Studio, which needs X Premium), LinkedIn and Instagram, paste the server and key. Your own player, CDN or OTT platform goes in as a custom RTMP destination.

  4. Decide what viewers see if the feed drops

    On the Control plan, choose a holding slate: a 'we'll be right back' card, your own message, a looping video or a slideshow. It takes over on every destination when the feed stops and stays until the encoder is back. Run it once as a test so the desk knows what it looks like.

  5. Route the alerts to the desk

    Turn on signal alerts for the stream and send them where the team already looks: email, Telegram, or a Slack, Teams, Discord or Google Chat channel through a webhook. They fire when the feed has been gone for a minute and again when it is back, and also when a single destination stops receiving.

  6. Watch the health panel, not the platforms

    During the broadcast, the health score and Stream Doctor flag low bitrate, a frozen or missing picture, dropped frames, silent or clipping audio and long keyframe intervals, each with the fix in plain words. A destination can be switched off and back on without touching the others.

  7. Keep the tape

    Switch recording on and the whole programme is saved to Storage, even if you press it after the show has started. Download it for the archive, schedule it to run again, or cut segments for social in Clips.

Feed settings for a multi-platform newsroom

Real values, taken from the limits StreamRove applies per platform. The bitrate row depends on which destinations are switched on.

Way inSRT in caller mode, 500 ms latencyRe-sends lost pieces of the stream; raise the latency on long or busy routes.
CodecH.264 video, AAC audioWhat the SRT and RTMP inputs accept.
Picture1920 × 1080, progressive, at 25, 30, 50 or 60 fpsLinkedIn takes 30 fps at most. Interlaced 1080i passes untouched only with Broadcast delivery.
Video bitrate6,000 kbps with Twitch or Facebook on the list, up to 8,000 with Kick, up to 12,000 for YouTube aloneThe strictest destination sets the number. For Facebook and YouTube these are the rates StreamRove plans; Facebook itself takes up to 9,000 at 60 fps.
Keyframe interval2 secondsStreamRove's health check warns above 4 seconds.
Rate controlCBR (constant bitrate)Platforms expect a steady rate.
AudioAAC, 48 kHz, stereo, 128 kbpsThe rate every destination accepts.

Lessons from newsrooms that stream every day

Treat every platform as its own audience

The same feed reaches people who arrived for different reasons: subscribers on YouTube, followers on Facebook, readers who saw a post on X. Write each platform's title and description for the people who find it there.

Remember that viewers join in the middle

Few people watch from the first minute. A lower third with the story's headline, refreshed every few minutes, tells newcomers where they are without the anchor repeating it.

Rehearse the failure, not only the show

Pull the encoder's cable during a test and watch what reaches the platforms: the slate, the alert, the reconnect. A team that has seen it once reacts in seconds on the night.

Know the rights before you go live

Platforms scan live streams for recorded music and some sports footage. A match can mute or stop the broadcast on that platform only; the other destinations keep receiving the feed and the story still gets out.

RTMP, RTMPS or SRT?

All three reach the same place. The difference is how they cope with the road in between.

Best forOlder encoders that offer nothing elseMost setups on a decent line; the defaultRemote sites, mobile networks, long distances
Encrypted on the wayNoYesDepends on the connection details shown for your stream
When the line loses dataStalls, and may disconnectStalls, and may disconnectRe-sends what was lost; viewers usually notice nothing
Delay it addsVery littleVery littleThe latency you set, 500 ms by default
Where to find itThe RTMP tab of the connection detailsThe RTMPS tab, selected by defaultThe SRT tab

Trusted across media

News networks

Breaking coverage to every screen.

Digital publishers

Live shows that grow subscribers.

Sports media

Game-day streams without delay.

Radio & podcasts

Simulcast audio and video live.

Frequently asked questions

Can we send one newsroom feed to every platform at once?

Yes. Point your existing encoder — OBS, vMix, a hardware unit — at one StreamRove RTMP, RTMPS or SRT URL and we fan it out to YouTube, Twitch, Facebook, Kick and any custom RTMP destination. Your production workflow does not change; only the number of places it lands does.

What happens if the connection to one platform drops mid-broadcast?

Each destination is a separate outbound session, so one failing does not interrupt the others or your ingest. The live health score and Stream Doctor flag the problem while you are still on air, and you can toggle a destination off and back on without stopping the broadcast.

Can we run a rehearsed segment inside a live show?

Play it from your own mixer: add the file as a media source in vMix or OBS and cut to it like any other source. For a whole pre-recorded programme, Upload & stream plays a rundown of videos to the same destinations at a set time, with trim points and a loop or filler at the end.

Do you keep a recording of what went out?

On paid plans, switch recording on and the whole broadcast is captured, landing in Storage when it finishes, so an editorial team can pull the tape without a separate capture rig. Download what you need to keep: recordings follow your plan's retention period.

Is there a backup input for a second encoder?

No. Each stream takes one feed at a time. What StreamRove adds is the holding slate on the Control plan, which keeps a drop from looking like the end of the broadcast, and alerts that reach the team within a minute.

Can we send interlaced 1080i?

On the standard route, platforms receive progressive video, and a 1080i50 feed arrives as 25 frames per second. With Broadcast delivery (Relay plan and up), the relay forwards your signal untouched, interlacing included, to the destinations you choose.

Can we send to our own player or CDN?

Yes. Anything that accepts an RTMP or RTMPS address and a key is a custom destination, alongside the platforms. With Broadcast delivery, SRT destinations in caller mode work too.

Does adding platforms cost picture quality?

No. The feed is passed on as it arrives rather than re-encoded for each platform, so the tenth destination gets the same picture as the first. The exceptions are the free plan, where a small StreamRove mark is drawn into the picture, and your own logo, when you add one.

Keep reading

From the blog

Put your newsroom on every screen

Broadcast live to every platform with the reliability your audience expects.

Sign up for free