Skip to content
Guide · vMix

vMix multistream for professional productions

Send one programme feed from vMix to YouTube, Twitch, Facebook, Kick and any RTMP destination. vMix sends a single stream to StreamRove over RTMP or SRT, and the copies for each platform are made on our side. The venue's upload carries one stream, however many platforms are watching.

Written for multi-camera shows, hybrid events and outside broadcasts, where the internet line is usually the weakest link in the chain.

1
Stream out of vMix
RTMP · SRT
Ways in from vMix
500 ms
SRT latency to start with
2 s
Keyframe frequency

Why production teams route vMix through StreamRove

The venue line carries one stream

vMix can stream to up to five destinations by itself, but each one is a full stream on the venue's upload. Through StreamRove, a 6,000 kbps show needs about 9 Mbps up, whether it reaches two platforms or every one your plan allows.

SRT for lines you don't trust

Event Wi-Fi and mobile routers lose data. SRT re-sends what goes missing within the latency you set, where RTMP stalls and reconnects. vMix sends SRT as an output, and StreamRove delivers your programme to every platform over the RTMP or RTMPS address it expects.

Someone watching the feed with you

A 0–100 health score and Stream Doctor's plain-language notes flag a falling bitrate, dropped frames, a frozen picture or silent audio while you're live. The director hears about it before the client does.

A plan for when the line drops

Signal alerts reach you by email, on Telegram or in a Slack, Teams or Discord channel once the signal has been gone for a minute. On the Control plan and up, a holding screen keeps the client's channels live until vMix reconnects.

StreamRove features that matter in a production truck

RTMPS, RTMP and SRT ways in

Use vMix's Custom RTMP Server with your stream's URL and key, or its SRT output in Caller mode. Both reach the same destinations, recording and health checks.

An Output profile for your mix

The Output profile card on the stream page lists the bitrate, frame rate, keyframe interval and audio bitrate that suit every destination you added, and names the platform behind each limit.

A holding screen instead of dead air

On the Control plan and up, the Backup stream card puts a holding screen, a countdown, a looping video or a slideshow on air when vMix drops, and hands back when it returns. It covers the gap; it isn't a second feed.

Stream Doctor in plain words

Rule-based checks turn the numbers into sentences with the fix attached, such as 'Your bitrate is too high for Twitch. Reduce it to around 6000 kbps.'

Platforms on switches

Add, remove or switch a destination off and on from any browser while you're live, without touching the vMix machine. Each one shows Reaching, Connecting… or Not reaching.

A recording for the client

On paid plans, press Save recording and the whole programme lands in Storage as an MP4, even if you press it after the show has started.

vMix's own destinations, or one stream to StreamRove?

vMix can stream to several platforms by itself. The difference is what the venue's line and the vMix machine have to carry.

StreamRovevMix streaming to each platform
Upload for three platforms at 6,000 kbps✓ About 9 Mbps: one streamAbout 26 Mbps: three streams
How many platforms✓ As many as your plan allowsUp to five streaming destinations
SRT from the venue✓ SRT in, RTMP out to every platformOnly to receivers that accept SRT
A different bitrate per platform— No: one stream fits all✓ Yes: untick Use Stream 1 Quality
Changing platforms mid-show✓ From any browser, without touching vMixOn the vMix machine
Watching the stream's health✓ Health score, Stream Doctor and alertsView Status in vMix's streaming window
If the venue line dropsHolding screen on Control and up; Signal alerts on every planEvery destination drops

How to multistream from vMix, step by step

Do this on the vMix machine at the venue, ideally the day before the show.

  1. Create the stream in StreamRove

    Click New Stream, choose Encoder | RTMP and name it after the show. Under Your Channels, add the client's platforms: YouTube, Twitch and Kick connect in one click; Facebook, LinkedIn and the rest take a server and key.

  2. Decide how vMix reaches StreamRove

    On a wired line you have tested, use RTMPS or RTMP. On shared Wi-Fi, a mobile router or a long route, use SRT. Measure the venue's upload with the bitrate calculator from the machine you'll stream from.

  3. RTMP: fill in vMix's Streaming window

    Click the cog next to the Stream button. Set Destination to Custom RTMP Server, paste the RTMPS or RTMP URL from your stream page into URL and the stream key into Stream Key (some versions call it Stream Name or Key). Pick a Quality preset, or click its cog to enter the values from the table below.

  4. SRT: set it up as an output

    Open vMix Settings → Outputs and click the cog next to the output you want to send. Tick Enable SRT and set Type to Caller, Hostname live.streamrove.com, Port 8890 and Latency 500. Paste the Stream ID from the Separate fields on your stream's SRT tab and leave Passphrase empty.

  5. Match the stream to the platforms

    Send 1920 × 1080, progressive, as H.264 with AAC audio and a keyframe every 2 seconds. Use the bitrate your strictest destination allows, 6,000 kbps with Twitch or Facebook, and 25 or 30 fps when LinkedIn is on.

  6. Test with the destinations off

    Start the stream in vMix with every destination switched off. The preview appears on your stream page about 10 seconds after vMix connects. Check the picture, the sound from the desk and the Output profile card.

  7. Arm the safety nets

    Press Save recording (paid plans) and switch Signal alerts on. On the Control plan and up, choose what the Backup stream card shows, stop vMix's stream and press Test backup now: the crew should see the holding screen once before the show.

  8. Go live before the doors open

    Switch the destinations on ahead of the start. Each should change to Reaching; check anything that shows Not reaching before the audience arrives, and open every platform on a phone.

vMix settings that suit every platform

Values for vMix's Streaming Quality window (RTMP) or its SRT output settings. The strictest destination sets the bitrate, because one stream goes to all of them.

Format / Video CodecH264StreamRove and every platform take H.264. vMix's HEVC and AV1 need a supported GPU, and few platforms accept them.
Encode Size1920 × 1080, progressiveThe largest size every platform plays. vMix's SRT output supports progressive formats only.
Frame rateYour production's: 25, 30, 50 or 60LinkedIn takes 30 fps at most; with it on, stream at 25 or 30.
Video Bit Rate6,000 kbpsTwitch takes 6,000 at most, and 6,000 sits inside Facebook's range at both 30 and 60 fps. The SRT tab suggests up to 6 Mbps.
ProfileMain or High, not BaselinevMix's own help calls Baseline the lower-quality choice; it only saves CPU.
Presetveryfast, or Low Latency HQ with NVENCvMix's recommended balance of CPU load and quality.
Keyframe Frequency2 secondsvMix's default and what platforms expect. StreamRove flags anything above 4 seconds.
AudioAAC, stereo, 128 kbpsAccepted by every destination; 160 only when Twitch and Kick are the only ones.
SRT Latency500 msStreamRove's starting point. vMix advises at least four times the ping to the server; raise it on long or busy routes.
SRT CBRTicked, with the video bitrate about 10% lowervMix pads SRT to a constant rate, which adds roughly 10% on top of the bitrate you set.

vMix labels from its user guide (version 29). In the SRT output, Hostname and Port come from the line under Separate fields on your stream's SRT tab.

What crews learn after a few vMix shows

When the picture stutters, change the route first

vMix's built-in encoder can drop frames on RTMPS where plain RTMP from the same machine runs clean (the FAQ below has our test). Before you blame the venue line, switch to the RTMP address or to SRT. If your stream page says 'Your broadcast is arriving unevenly', use the StreamRove address it offers: a short hop to our server rather than a long one to the provider.

Give the stream its own output

In vMix 4K, Pro and Max, the Source setting in Streaming Quality can send Output 2, 3 or 4 instead of Output 1. That lets the stream carry a clean programme while the screens in the hall show something else, such as a confidence feed or graphics meant only for the room.

Count the graphics card's jobs

vMix's SRT output encodes on the graphics card, and vMix recommends an NVIDIA Quadro P2000 or better; GeForce 9xx cards and older aren't supported for SRT. Streaming, SRT and recording with the hardware encoder all draw on the same chip, and GeForce cards cap how many encodes run at once. List the jobs before the show and drop one if the card is near its limit.

Record in vMix as well

Keep vMix recording to its own disk while StreamRove saves the broadcast on a paid plan. The local file is your full-quality master if the line has a bad patch. StreamRove's recording is what viewers actually received, waiting in Storage when the show ends and easy to share with the client. A recording made with the hardware encoder counts as one of the graphics card's jobs.

Frequently asked questions

Can vMix send SRT to StreamRove?

Yes. In vMix, SRT is an output: Settings → Outputs, the cog next to an output, Enable SRT, Type Caller. Use Hostname live.streamrove.com, Port 8890, Latency 500 and the Stream ID from your stream's SRT tab, with no passphrase. StreamRove accepts H.264 video with AAC audio over SRT. More on the protocol in our SRT guide.

Is the SRT connection encrypted?

Not on StreamRove's SRT address. It uses no passphrase, and the stream travels unencrypted, as it does over plain RTMP. If the route needs encryption, use the RTMPS address instead, which wraps the stream in TLS.

RTMP or SRT from vMix: which should I use?

RTMPS or RTMP on a wired line you've tested; SRT on shared Wi-Fi, mobile routers or long routes, because it re-sends lost data instead of stalling. SRT adds the latency you set, 500 ms to start with.

vMix drops frames on RTMPS. What should I try?

Switch vMix's URL to the plain RTMP address from the same stream page, or move to SRT. In our own test on 16 September 2026, vMix's encoder dropped frames on RTMPS while 94 minutes of plain RTMP from the same machine stayed clean. Treat it as practical advice rather than a guarantee: if frames still drop, lower the bitrate and check the CPU.

Can I stream 1080i from vMix?

Platforms play progressive video. On StreamRove's standard route a 1080i50 feed arrives as 25p, and vMix's SRT output supports progressive formats only. Set the stream to 1080p25 or 1080p50. If a receiver of your own needs the signal untouched, Broadcast delivery (Relay plan and up) forwards it as it arrives, provided vMix sends to the StreamRove ingest: the SRT address or the StreamRove RTMP address.

What happens if the venue internet fails mid-event?

With Signal alerts on, you're told once the signal has been gone for a minute, and again when it's back. On the Control plan and up, the Backup stream card holds every destination with a holding screen until vMix reconnects. It covers the gap; StreamRove doesn't take a second encoder as a backup.

Do I need StreamRove if I only stream to two platforms?

Not always. If the venue line can carry two full streams, vMix can send them itself. StreamRove earns its place when the upload is tight, when you want SRT in and RTMP out, when the client wants alerts or a holding screen, or when platforms have to change mid-event without anyone touching the vMix machine.

Which vMix editions can output SRT?

According to vMix's edition comparison, Basic HD and HD have one SRT output, and 4K, Pro and Max have four. SRT output also needs a graphics card that can encode H.264: check vMix's requirements on the machine you'll take to the venue.

Keep reading

From the blog

Put your vMix show on every platform

One stream out of the venue, every platform on a switch, and an alert if the line drops.

Sign up for free